MarineDieselXRef

Home › Engines › Beta 20

Beta 20 Marine

Beta Marine Beta 20 · BETA family: specifications, its industrial/tractor base engine, cross-referenced parts and where to buy them.

🚜 Base engine confirmed

The Beta 20 (Beta code BD722) is a marinized Kubota D722 industrial block; its internal service parts cross to Kubota D722 part numbers. source

20 hp14.7 kW

719 ccdisplacement

67×68 mmbore × stroke

3-cylcylinders

from 2011year range (approx)

NAaspiration

📋 Full specifications 8 🚜 Industrial / tractor base 419 🔧 Aftermarket 38

Cheaper-part coverage · 8/8

🚜 Base engine ✓🌀 Impeller ✓💧 Raw-water pump ✓🛢️ Oil filter ✓⛽ Fuel filter ✓🌡️ Thermostat ✓➰ Belt ✓⚓ Anode ✓

A ✓ means at least one cheaper channel — aftermarket, the tractor/industrial base engine, or a standard component — exists for this engine in that category.

Parts by section · 132 assemblies

The exploded parts diagrams for the Beta 20, grouped by system. Open a figure for its callout part numbers and per-variant quantities.

Cooling

Fig P10 — Keel cooled header tank -Cast tanks: Beta10, Beta14 & Beta20 to Mid 2002 Fig P13 — Heat exchange tank -Cast tanks: Beta 10, Beta 14 & Beta 20 to Mid 2002 Fig P14 — Heat exchange tank -Beta 10 / Beta 14 Fig P15 — Heat exchange tank - Beta 16 Fig P16 — Heat exchange tank -Beta 20 Fig P17 — Heat exchange tank - Beta 25(2011 Spec 3 Bolt Manifold Shown)Fig P18 — Heat exchange tubestack (2011 SPEC HEAT EXCHANGER MANIFOLD)Fig P19 — Heat exchange tubestack (with 22mm header & anode on aft end) From January 2002 Fig P24 — Sea water cooling pipe -From June 2013 Fig P11 — Beta 14, 16, 20 & 25 (non turbo) Greenline 3 Bolt Keel Cooled Manifolds - From 2011 Fig P10 — Keel cooled header tank -Cast tanks: Beta 10, Beta 14 & Beta 20 to Mid 2002 Fig P14 — Heat exchange tank -Beta 10 & Beta 14 Fig P17 — Heat exchange tank - Beta 25 (2011 Spec 3 Bolt Manifold Shown)

Drive Plate

Fig P44 — Gearbox driveplate

Electrical & Controls

Fig P57 — Alternator -12 Volt 65 Amp (Beta 10, Beta 14 & Beta 20 Only) to December 2010 Fig P63 — Simple 2A panel -LED type to May 2005 Fig P64 — Simple 2A panel -LAMP type from May 2005 Fig P65 — 2AB panel -LED type to May 2005 Fig P66 — 2AB panel -LAMP type from May 2005 Fig P67 — 2AB'V' panel -LAMP type to May 2005 Fig P68 — 2AB'V' panel -LAMP type from May 2005 Fig P69 — 2AB'V'W pushbutton control panel -LAMP type from May 2005 Fig P71 — SFIA 2B panel -LAMP type to May 2005 Fig P72 — SFIA 2B panel -LAMP type from May 2005 Fig P73 — Murphy deluxe 2C panel & senders -Seaspec 4 Lamp-to May 2005 Fig P74 — Murphy deluxe 2C panel & senders -Domestic 5 Lamp -to May 2005 Fig P75 — Murphy deluxe 2C panel & senders -Domestic 5 Lamp -from May 2005 Fig P76 — Panel gauges & senders Fig P77 — VDO Gauge accessories Fig P78 — Various electrical & panel parts and components Fig P27 — Wiring Harness & Switches Fig P28 — IPL AB Panel - LED Type to May 2005 Fig P29 — AB Panel - LAMP Type from May 2005 Fig P30 — IPL ABV Panel - LED Type to May 2005 Fig P31 — ABV Panel - LAMP Type from May 2005 Fig P32 — IPL Deluxe C Panel - SeaSpec 4 LAMP Type to May 2005 Fig P33 — Deluxe C Panel - Domestic 5 LAMP Type to May 2005 Fig P34 — IPL Deluxe C Panel - SeaSpec 5 LAMP Type from May 2005 Fig P35 — Panel Gauges and Senders Fig P36 — IPL Gauge Components Fig P37 — Control Panel Components Fig P64 — Alternator Accessories-12 Volt 55 & 65 Amp (Beta 10, Beta 14 & Beta 20 Only)Fig P76 — 2BW pushbutton control panel -LAMP type from May 2005 Fig P80 — 2CW Push button control panel -sea spec 4 lamp, from May 2005 Fig P81 — 2D Digital control panel

Engine

Fig P30 — Thermostat housing Fig P5 — Header tank manifold fixings -Cast tanks, Beta10, Beta14 & Beta20 to Mid 2002 Fig P56 — Alternators -12 Volt 40 & 60Amp -to January 2011 Fig P83 — Electrical, Oil system & Miscellaneous Fig P10 — IPL Beta 14, 16, 20 & 25 (non turbo) Greenline 3 Bolt Keel Cooled Manifolds - From 2011 Fig P12 — IPL Beta 14, 16, 20 & 25 (non turbo) Greenline Keel Cooled Oil System Components Fig P21 — Beta 14, 16, 20 & 25 (non turbo) Greenline Keel Cooled Fuel System Components Fig P6 — Keel Cooled Fig P36 — Front mounted fuel filter system - From December 2005 Fig P5 — Header tank manifold fixings -Cast tanks, Beta 10, Beta 14 & Beta 20 to Mid 2002

Exhaust

Fig P28 — Water injection bends -Standard options Fig P29 — Water injection bends -non standard Fig P48 — Gearbox -PRM 80 & 120 Gear control brackets Fig P16 — IPL Beta 14, 16, 20 & 25 (non turbo) Greenline Keel Cooled PRM80, 90, 120 & 125 Morse Control Brackets Fig P23 — Beta 14, 16, 20 & 25 (non turbo) Greenline Keel Cooled Speed Control Bracketry & Feet Fig P49 — Gearbox -PRM 80, 90, 120 & 125 Gear control brackets

Fast Moving

Fig FAST — Fast Moving Parts List

Fasteners

Fig P26 — Sea water cooling pipe -To October 2002 Fig P31 — Air inlet manifold & fuel system-Beta10, Beta14 & Beta20 to December 2005 Fig P32 — Air inlet manifold -Beta 10 / Beta 14 & Beta 16 From December 2005 Fig P33 — Air inlet manifold -Beta20 From December 2005 Fig P34 — Air inlet manifold -Beta 25 From December 2005 Fig P38 — Flywheel housing 080 020 Fig P39 — Speed control bracket -Beta 10, Beta 14 & Beta 16 only Fig P40 — Speed control bracket -Beta 20 only Fig P41 — Speed control bracket -Beta 25 only Fig P42 — Front feet Fig P43 — Rear feet Fig P45 — Driveplate spacer ring Fig P47 — Gearbox -TMC 40 Gear control brackets Fig P51 — Sump drain pump -Components Fig P53 — Alternators -12 Volt 40 Amp -from January 2011 Fig P54 — Alternators -12 Volt 75 Amp -from January 2011 Fig P55 — Alternator -12 Volt 100 Amp -from August 2014 Fig P58 — Alternator -12V 65A (Beta10, Beta14 & Beta20 Only) From Jan 2003-Dec 2010 Fig P6 — Header tank manifold fixings -Beta 10 / Beta 14 Fig P61 — Alternator Accessories-12 Volt 55 & 65 Amp (Beta 10, Beta 14 & Beta 20 Only)Fig P7 — Header tank manifold fixings -Beta 16 Fig P8 — Header tank manifold fixings -Beta 20 (2011 Spec 3 Bolt Manifold Shown)Fig P9 — Header tank manifold fixings -Beta 25 (2011 Spec 3 Bolt Manifold Shown)Fig P13 — Beta 14, 16, 20 & 25 (non turbo) Greenline Keel Cooled Oil System Components Fig P24 — IPL Beta 14, 16, 20 & 25 (non turbo) Greenline Keel Cooled with 40 Amp Alternator - From January 2011 Fig P25 — Beta 14, 16, 20 & 25 (non turbo) Greenline Keel Cooled with 75 Amp Alternator - From January 2011 Fig P26 — IPL Beta 14, 16, 20 & 25 (non turbo) Greenline Keel Cooled with 100/120 Amp Alternator - From Jan. 2011 Fig P31 — Air inlet manifold & fuel system-Beta 10, Beta 14 & Beta 20 to December 2005 Fig P32 — Air inlet manifold -Beta 10, Beta 14 & Beta 16 From December 2005 Fig P33 — Air inlet manifold -Beta 20 From December 2005 Fig P58 — Alternator -12 Volt 100/120 Amp -from August 2014 Fig P6 — Header tank manifold fixings -Beta 10 & Beta 14 Fig P61 — Alternator -12V 65 Amp (Beta 10, Beta 14 & Beta 20 Only) From Jan 2003-Dec 2010 Fig P88 — PTO Shaft & pulley -all engines from 2011

Filters

Fig P37 — Air filter

Fittings & Hose

Fig P11 — Keel cooled header tank -Beta 10 / Beta 14 / Beta 16 Fig P12 — Keel cooled header tank -Beta 20 / Beta 25 (2011 Spec 3 Bolt Manifold Shown)Fig P25 — Sea water cooling pipe -From December 2010 to June 2013 Fig P27 — Sea water cooling pipe -From October 2002 to December 2010 Fig P35 — Sea spec fuel system -to suit side mounted fuel filter to June 2005 Fig P36 — Front mounted fuel filter system - From December 2005 Fig P49 — Gearbox -TMC 60 Gear control bracket Fig P50 — Shallow sump Fig P79 — Expansion water bottle & spare parts list -all engines Fig P80 — Water drain components -all engines Fig P84 — Installation Kits Fig P85 — Fuel / water separator Fig P17 — Beta 14, 16, 20 & 25 (non turbo) Greenline Keel Cooled TMC60 Morse Control Brackets Fig P19 — Beta 14, 16, 20 & 25 (non turbo) Greenline Keel Cooled Fuel System Components Fig P38 — IPL Expansion Tank Kits Fig P39 — Beta 14, 16, 20 & 25 Greenline Keel Cooled Calorifier Kit - From 2011 Fig P40 — IPL Installation Kits Fig P41 — Fuel/Water Separator Fig P8 — Keel Cooled Fig P11 — Keel cooled header tank -Beta 10, Beta 14 & Beta 16 Fig P12 — Keel cooled header tank -Beta 20 & Beta 25 (2011 Spec 3 Bolt Manifold Shown)Fig P48 — Gearbox -PRM 60 Gear control brackets

Gearbox

Fig P46 — Gearbox

Lubricating

Fig P52 — Sump drain pump -hose assembly From December 2002 Fig P14 — IPL Beta 14, 16, 20 & 25 (non turbo) Greenline Keel Cooled Oil System Components Fig P7 — Beta 14, 16, 20 & 25 (non turbo) Greenline Keel Cooled - From 2011 Starboard View

Sea Water Pump

Fig P20 — Heat exchange sea water pump -Johnson Fig P21 — Heat exchange sea water pump -Jabsco -engines to July 2006 only Fig P22 — Heat exchange sea water pump -Beta type from June 2013

Other

Fig P70 — Service kit to suit 2AB'V'W pushbutton control panel Fig P82 — Calorifier connections / hot water take off -Keel cooled & Heat Exchange pre Dec2010 Fig P86 — Short Voyage Spares Kits Fig P42 — IPL Beta 14, 16, 20 & 25 (non turbo) Greenline Keel Cooled 6K Polyvee 1st Alternator Drive Upgrade Kit - From 2011 Fig P43 — Beta 14, 16, 20 & 25 (non turbo) Greenline Keel Cooled 75 Amp Alternator Upgrade Kit - From 2011 Fig P82 — NMEA2000 Digital interface -for installations with deluxe control panel

📚 Manuals & Sources

Specs

Beta 20 H/E Engine Data Sheet Mfr Beta Marine

Operator's Manual— none yet

Service / Workshop Manual— none yet

Parts Catalog / List

Beta 10-25 Illustrated Parts List Mfr Beta Marine

More📖 Boat Inboard Engine Manuals Boat Manuals

External links — we host none of these documents.

Beta 20 — Affiliate Parts Search

Amazon eBay AliExpress

As an Amazon Associate I earn from qualifying purchases. Other links (eBay, AliExpress) are also affiliate links — they help pay for the site, at no extra cost to you. More

Category: Marine
Engine family: BETA
Year range (approx): from 2011
Cylinders: 3
Rated output: 20 hp (14.7 kW)
Bore × stroke: 67 × 68 mm
Displacement: 719 cc
Max rpm: 3600
Aspiration: Naturally aspirated

Related BETA engines

Beta 10 Beta 105T Beta 115T Beta 14 Beta 150 Beta 16 Beta 25 Beta 28 Beta 30 Beta 35 Beta 38 Beta 43 Beta 45T Beta 50 Beta 60 Beta 62T Beta 70T Beta 75 Beta 85T Beta 90 Beta 90T